Fixed furniture: construction methods and measures of wood veneer with wooden hanging board
1. Technological process of fixed furniture
Elastic line, arrangement of moisture proof layer, keel installation, installation, decorative plate installation on base plate.
2. Construction methods and technical measures of fixed furniture
1 Line: according to the size requirements of the design drawings, draw on the wall to rise horizontally and pop up the dividing line. According to the dividing line of the wall at the position of the wooden nail, it should be consistent with the size of the keel. The horizontal and vertical spacing is generally 300 mm, not more than 400 mm.
2 Dampproof course installation: the wooden wall must be treated with dampproof course before construction. The general practice is to brush two water asphalt on the base plate or keel.
3 Wooden keel installation of fixed furniture
When the moisture content of the wooden keel is less than 12%, the wooden keel shall be fireproof. The fireproof coating can be applied to the wooden flutes on both sides, washed twice, dried and reassembled.
According to the design requirements, use wood as support, whole piece or sub assembly. The whole wall finish should be based on the four corners of the room and the upper and lower keel leveling, straight, according to the panel block size from top to bottom do wood marking rib, but according to the neutral nail design requirements of horizontal and vertical keel.
If there is no gap between the keel and the wall base, it is also used to check the levelness of the solid wedges. If there is no gap between the keel and the wall base, it is also used to check the levelness of the solid wedges And the keel and nail, and each wooden keel must be nailed down, at a fixed angle staggered each block and keel two nails.
4 Installation of fixed furniture base plate
The project enables 9 plywood to be installed on the keel as the basic installation, lying flat firmly without deformation. The surface, such as concave or convex, needs to be corrected. Some traces of dust and plastic particles are left on the adhesive layer. The nail head should be completely removed or smoothed.
5 Panel installation of fixed furniture
(1) Has produced a good wooden base pop-up elevation line, horizontal, dividing line, construction planning requirements, check the smooth surface of the wooden base and vertical, internal and external angle triangle plate. The frame material of wood base must be dry and high quality plywood, and the flatness and adhesion must meet the requirements.
(2) Select color wood plywood, divided into different colors, texture, according to the requirements of blanking, try to spell, the same or similar wood consistent with the color of decorative board together, the nature of wood grain butt joint, irregular paper burr should be corrected plane quadrilateral, micro thin board should first floor, and then paste. The water-based paint veneer should avoid direct fighting connection as far as possible. The decorative panel should be painted on the back of three sides of fire-retardant paint. At the same time, the hidden surface must be covered with paint to avoid cracking, easy to clean, avoid rubbing the surface, and avoid local stress during construction. Hammering is strictly prohibited. High grade plywood construction workers wear white gloves to operate.
(3) The wood powder is evenly coated on the back of the veneer and wood base, facing the plate pad 9mm multi-layer floor. After the strip steel nail gun hits, the glue is dry, and the lath and nail gun are cleaned down. Play bar and air gun nail must have wood pad to prevent local stress and damage surface coating.
(4) Decorative wood line must be uniform color, smooth, tight seam, nail gun nail must be hidden parts, decorative wood line material must be dry, moisture content must be consistent with the requirements of color and texture, meet the design requirements, the line's machine surface must be oil-free, the wood surface must be smooth sand, paint back cover, color selection and transportation to the site.
(5) Direct fixed finish must be constructed with line nailing gun. In the case of thin plate, according to the requirements that some decorative boards are installed on two surfaces and coated with glue on the basis of density board and multi-layer board, the glue must be evenly coated, the glue and operation must be neat, and the glue should be non hand glued again, and the cushion block on the board should be hammered with a wooden block.
(6) It is strictly forbidden to use heavy iron sand cloth, sand surface, a trace of plastic and pencil needle on the surface.
(7) Planing veneer when all solid wood edges are cut. Careful construction, strengthen the protection of finished products, avoid corner touch.